#1 Rated Handyman
House Spouse

Ask House Spouse · Exterior & Weatherproofing · Decks & Outdoor Structures

How much does it cost to refinish a deck in the Seattle area?

Short answer

Refinishing an average 300 to 400 square foot deck in Western Washington typically costs between $1,200 and $3,200. Pricing depends on board condition, railing complexity, required board repairs, and whether you need a simple wash and recoat or intensive chemical stripping and sanding.

DK
Founder · Licensed WA Contractor · 20+ years
(206) 335-7334

Breaking down square-foot pricing in King and Snohomish County

Most deck refinishing jobs in our service area pencil out to roughly $4 to $8 per square foot for standard flat deck surfaces. That range climbs to $8 to $12 per square foot when you add intricate railings, stairs, and wrap-around fascia. The biggest labor driver is never rolling the stain. The real cost lies in preparation, because applying expensive stain to damp or dirty wood is throwing money into the wind.

The hidden cost of stripping failed solid stains

If a previous owner applied a solid, paint-like deck coating that is now flaking, your refinishing costs will sit at the top of the price range. Pressure washing alone will gouge soft cedar fibers before it removes stubborn acrylic coatings. Stripping requires commercial biodegradable strippers, neutralizing washes, and heavy floor sanding once dry. This easily doubles prep labor compared to refreshing a quality semi-transparent penetrating oil.

Repairs that should happen before the stain opens

Refinishing is the ideal time to handle carpentry punch-list items. Replacing a couple of badly cupped cedar boards, sinking popped screws, securing a loose stair tread, or replacing degraded railing caps protects your investment. We often bundle these minor structural repairs into our standard $580 four-hour handyman visit before the cleaning phase begins, ensuring the entire structure is stable and dry.

Timing the job around Western Washington weather

You cannot rush deck staining in the Pacific Northwest. Wood must have a moisture content below 15 percent before applying oil or water-based stains. That usually means waiting for a reliable dry stretch between late June and mid-September. Pressure washing in early spring is fine, but coating too early locks winter groundwater inside the cellular structure of the wood, causing the new finish to blister and peel by Thanksgiving.

Why it happens

Our maritime climate is brutal on exterior horizontal wood. Between eight months of steady rain, low winter sunlight, and constant pine needle accumulation, moisture penetrates unprotected timber. This breeds surface mold, algae, and wood-destroying fungi that lift existing finishes and leave raw cedar or fir exposed to summer UV baking. When a deck finish fails in Puget Sound, simple pressure washing is rarely enough. The wood fibers swell and soften under prolonged dampness. Refinishing costs vary wildly because a deck that only needs a gentle wash and maintenance coat requires a fraction of the labor compared to one suffering from peeling solid stain, splintering surfaces, or rusted structural fasteners that demand board replacement before stain touches the wood.

How to diagnose it

  1. 1Perform the water drop test: pour a few tablespoons of water onto high-traffic and sheltered boards. If it beads, the seal is working. If it soaks in within two minutes, your finish has failed.
  2. 2Inspect the railings and balusters for peeling: handrails take direct rainfall and usually fail a full season before the vertical spindles.
  3. 3Check for wood softness: press a flathead screwdriver into board ends, stair stringers, and around fastener holes to ensure you are dealing with surface wear rather than structural rot.
  4. 4Look for raised grain and splintering: boards that have sat bare through a wet winter often need machine sanding, which increases labor time significantly.
  5. 5Count cupped or cracked boards: factor in the cost of unscrewing and replacing degraded timber prior to any cleaning or staining work.

DIY vs. professional

DIY-friendly if…

Take on the job yourself if the deck is ground-level with sound boards and only requires gentle cleaning and a single transparent maintenance coat over the weekend.

Call a pro when…

Call a pro when dealing with multi-story railings, peeling solid film stains that require stripping and full sanding, or rotting boards that need structural carpenter repairs first.

Cost expectations

$1,200–$3,200typical WA labor + materials

Covers standard 300 to 400 square foot decks in King and Snohomish counties, including washing, light sanding, and two coats of quality penetrating stain.

Every House Spouse job is quoted in writing before we start. 12-month workmanship warranty included.

What we see on Home Health Assessments

74%of homes assessed

Around 74% of PNW roofs we assess show active moss establishment — accelerates shingle wear by an estimated 3–5 years if untreated.

Caught early on assessment: $220–$650 · Left until failure: $3,500–$22,000

During a Home Health Assessment, we check your deck ledger board, flashing, post bases, and joists for hidden rot before you spend money making failing boards look pretty.

How the Home Health Assessment works

Services we'd bring to this job

Where we handle this

We answer this question on real Home Health Assessments across Snohomish and King County.