Ask House Spouse · Exterior & Weatherproofing · Decks & Outdoor Structures
How much does it cost to build a 20x20 deck in the Pacific Northwest?
Short answer
In the Puget Sound area, building a 400-square-foot deck typically costs between $18,000 and $42,000 depending on materials, elevation, and railings. Pressure-treated framing with standard western red cedar sits at the lower end, while premium capped composite with aluminum or cable railings pushes toward the higher end.
Material cost breakdown: cedar versus composite
Western red cedar is the traditional Pacific Northwest choice. A 20x20 cedar deck generally runs between $18,000 and $26,000 completely installed. Cedar stays cooler underfoot in direct summer sun, but in damp, shaded neighborhoods like Lake Forest Park or Edmonds, untreated cedar easily fosters algae and rot. Capped composite or PVC decking pushes total project costs between $28,000 and $42,000. While expensive upfront, composite materials eliminate the need for regular pressure washing, stripping, and staining every two years.
Hidden cost drivers on Puget Sound properties
Site conditions often impact the final quote more than the decking surface itself. Decks built on sloped lots require engineered post bracing, deeper footings, and taller posts that increase structural framing costs. Railing choices also create wide variance. Basic pressure-treated wood railings are the most economical, whereas powder-coated aluminum, stainless steel cable, or tempered glass panels can add $4,000 to $9,000 to a 20x20 perimeter.
Rebuilding versus resurfacing an existing deck
You may not need to pay for a full rebuild from scratch. If your existing posts, beams, and joists pass a thorough moisture inspection without rot or insect damage, you can opt for deck resurfacing. This involves removing the old deck boards and railings, taping the top of the joists with butyl protective tape, and fastening fresh cedar or composite planks to the existing structure. Resurfacing a 20x20 deck usually costs between $8,000 and $16,000, saving substantial budget while providing a brand-new walking surface.
Permits, inspections, and ledger safety
In Washington State, residential decks higher than thirty inches above adjacent grade require a building permit and plan review. The ledger connection, where the deck anchors to your home rim joist, is the most critical failure point in our climate. Water trapped behind an un-flashed ledger rots the structural band board of the house over time. Proper professional installation requires z-flashing, specialized self-adhering membranes, and structural tension ties to comply with current residential building codes.
Why it happens
Deck building costs in Western Washington are heavily driven by wet-weather engineering requirements and material grades. Our relentless damp climate rots standard lumber quickly, which means code demands heavy galvanized or stainless steel hardware, proper flashing against ledger boards, and rot-resistant framing. High labor demand across King and Snohomish counties also sets baseline installation rates above national averages. Material selection creates the largest price split. While natural cedar remains a regional favorite, homeowners increasingly choose composite decking like Trex or TimberTech to avoid constant washing and sealing. Composite carries higher upfront material expense and requires closer joist spacing, but it avoids the premature fungal rot common to neglected wood decks in shaded Pacific Northwest lots.
How to diagnose it
- 1Check whether existing ledger boards and footings are structurally sound or if full excavation and new concrete piers are required.
- 2Measure deck height above grade to determine if safety railings, complex stair runs, and frost-depth footings are mandated by local building code.
- 3Decide between pressure-treated pine, western red cedar, or capped composite decking based on sun exposure and your willingness to perform annual maintenance.
- 4Inspect accessibility to the backyard, since steep Puget Sound slopes or tight side yards require manual hauling that adds to labor time.
- 5Confirm permit requirements with your city or county planning department for any deck over thirty inches above ground.
DIY vs. professional
DIY-friendly if…
Skilled homeowners can tackle a low-to-the-ground floating deck on flat ground using simple cedar planking and surface blocks.
Call a pro when…
Hire a licensed general contractor for elevated decks, ledger board attachment to house framing, slope engineering, or any project requiring city structural permits.
Cost expectations
$18,000–$42,000typical WA labor + materials
Reflects full professional installation of a 400-square-foot ground or second-story deck in King and Snohomish counties, ranging from cedar to premium composite.
Every House Spouse job is quoted in writing before we start. 12-month workmanship warranty included.
What we see on Home Health Assessments
About 41% of decks 12+ years old show ledger-board flashing gaps or corroded fasteners at critical connections.
Caught early on assessment: $280–$1200 · Left until failure: $2,500–$18,000
During a Home Health Assessment, we evaluate ledger flashing, post footings, and frame moisture levels to determine if you need a full replacement or simply board resurfacing.
How the Home Health Assessment worksServices we'd bring to this job
Where we handle this
We answer this question on real Home Health Assessments across Snohomish and King County.
